MustangWorks.com Classifieds - 86-93 Coupe - 11 second 1994 Z28 for trade

MustangWorks.com - The Ford Mustang Power Source!

Home · Search · Member List · Register

Home » Wanted to Buy » Mustangs and Fords

« Previous Ad · Next Ad »

86-93 Coupe - 11 second 1994 Z28 for trade

Contact Buyer

Views	Date Posted
37876	8/16/2006

Looking for:

Looking to sell this car outright or trade for 1986-1993 Fox body Mustang. I can sell/trade with or without the blower. Looking for a car of equal value - preferably an auto notchback. Will trade for a rolling chassis - but I will only make that trade minus my wheels/tires and blower.

$8000/OBO - Trades welcome.

1994 Chevrolet Camaro Z28 – I have owned this car for the past 4 years, I am currently the 3rd owner of this vehicle. The car is in good shape, excellent running order. I will break down all of the modifications into groups.
The car has ran a best of 11.37@120mph with the supercharger cutting consistent 1.6 60’ times on BF Goodrich Drag Radials. On motor only the car has run 12.36@110.82

The paint is in good shape, there are rock chips and the clearcoat is peeling off of the front nose section. There’s also a spot right under the fuel door that has lost paint.

This is a proven consistent low/mid 11 second street car that can be driven anywhere on pump gas. The car has only seen 93 octane or better (Never race gas) in it’s tank. The maintenance has been meticulous, as keeping up with a supercharged car of this caliber is a must. Simply lower the tire pressure and click off some 11 second passes – air up, pop the t-tops and cruise back home. It doesn’t get any better than that. At last dyno tune (April) the car put down 400rwhp/440rwtq with a conservative 26 degrees timing.

ENGINE Stock bottom end 1994 LT1 5.7 (350) GTP IV Camshaft 226/.236 .501/.526 114LSA Combination Motorsports EX612 valvetrain kit – hardened pushrods, springs, retainers, locks, seals, etc… www.cmotorsports.com Timing chain replaced at cam swap Stock untouched heads Crane Gold 1.6 Roller Rockers Powdercoated CSI electric Water Pump MSD 6A ignition box Taylor Over The Valve Cover wire kit (OTVC) NGK TR6 plugs Racetronix 255lph in-tank pump with plug-n-play harness www.racetronix.com Hypertech 160 degree t-stat

INDUCTION Vortech SQ trim supercharger Current pullies show 5lbs of boost Hard intake pipe BBK 52mm throttle body 42lb Motorsport injectors

EXHAUST Hooker SuperCompetition longtube headers – Jet Hot coated IRS 3” y pipe Flowmaster Force 2 cat back

DRIVETRAIN 1994 4L60E – professionally rebuilt in April by Baker Performance Automotive B&M Transmission Cooler Edge 3800 Pro Race torque converter 2001 SS Camaro rearend 3.42 gear

CHASSIS/SUSPENSION/MISC BMR lower control arms Competition Engineering 3 way adjustable rear drag shocks Competition Engineering 8pt roll bar kit (NOT INSTALLED) UMI Performance subframe connectors Summit racing seats – driver seat is double padded Rear seats removed AutoMeter Ultra Lite Boost and Water Temp gauge Car has been professionally dyno tuned by Bryan Herter @ PCMForLess Will include IBM A22M laptop, data cable and all tunes that the car has had over the years including the NA Dyno Tune

WHEELS N TIRES Centerline Telstar 15x4 front, 15x8 rears Front tires are 2 months old 165R15 Rear tires are BFG Drag Radials with about 1 season left on them

The car currently has no carpet in it as I removed for the installation of the roll bar kit – I was unable to complete this phase of the car. The T-Tops do not leak and the car has been garage kept for the last 3 years. I used it as a daily driver for the first couple of years until I bought another car. I continue to drive the car to work occasionally on nicer days which is roughly 70miles round trip.

I would replace the following items: Passenger side window motor (Drivers has already been replaced and the passenger is showing signs of wear. Carpet – after the roll bar install obviously. Vortech Elbow – the elbow that I received with the kit had been modified to work with a blow thru MAF – I did not like this setup and returned it back to the way that Vortech intended but I never replaced the elbow, only modified it to work.

For more pictures and videos please visit the following sites. If you need to, search for the username DarkHorse www.rubbercityracing.com - www.camaroz28.com - http://camaroz28.cardomain.com/id/zyal8tr - http://media.putfile.com/Norwalk-Track-Rental

Keywords:

11 sec Z28

Wanted By
	RPM_Racer Registered Member		0 Registered: August 2006 Ads from this Seller

« more ·

<<<

http://classifieds.mustangworks.com/data/16/thumbs/3299790_stang_3.jpg

>>>

· more »

All times are GMT -5. The time now is 05:52 PM.